I hope this question isn't asked ever 5 minutes.
Got my first package of bees 4 days ago. Went in for my first inspection today and they've built a big piece of comb hanging from the underside of the inner cover. I have one 8 frame medium with frames and one empty medium with a gravity feeder in it.
If I just need to add a body with new frames, how do I get the bees off the renegade hanging comb and clean up this mess?
Thanks,
Marc
Shake them off the comb. Remove the comb and attach it to a frame.
Got it. Thank you.
Using a mat ontop of the frames adds a barrier that makes them less eager to put comb on the lid.
Quote from: omnimirage on May 07, 2016, 06:06:53 AM
Using a mat ontop of the frames adds a barrier that makes them less eager to put comb on the lid.
and encourages SHB so be on your toes
Quote from: Psparr on May 06, 2016, 01:43:53 PM
Shake them off the comb. Remove the comb and attach it to a frame.
What's your preferred method to attach comb to a frame?
It does? I suppose that makes sense, gives them a safe haven. I've always used one, as was taught by me. The few times I haven't, I found that the bees built burr comb all over the lid. Is it not standard to use a hive mat? Is there merits for not using one? One of my sites is now infected with SHB.
I second yes2matt's question. What is a good way to attach loose comb to a frame (an empty foundationless frame in my case).
Rubber bands. If it doesn't reach the bottom bar, just press the wax onto the top bar and have the rubber bands for lateral support.
Quote from: Psparr on May 11, 2016, 03:38:12 PM
Rubber bands. If it doesn't reach the bottom bar, just press the wax onto the top bar and have the rubber bands for lateral support.
Sorry to be a dim bulb, I'm understanding you to mean to put a rubber band longways around the whole frame, with the comb installed there, so the bees will just work around it until they get the sides/bottom attached, then remove the rubber band later. I was going to try something much more difficult. :)
Make sure you put the comb in the same way it came out of the hive. Cells are slightly tilted upward. If you put it in upside down it'll just hang there. The bees may re work it but I don't know.
This is a new package. You are feeding them. They are building comb. Don't worry about attching this wax to the top bar of the frame. Put four rubberbands around the top and bottom bar of the frame. Cut the comb and rest it on the bottom bar of the frame, all the way to the side of the frame so that it touches the side-bar. Slide the rubber bands over the comb to hold it upright. By the way, the wax is probably too sift for an of this. If you can't salvage it, don't worry.
For your feeder set up....If you are going to put an empty box on top of a colony, you should probably fill the void space around the feeder with crumpled up paper of some kind. It's a void space in the cavity where the bees are building their home. It is natural for them to go as high as they can in the void, and start building. It would be simpler to get a division board feeder, or go with one of those screened feeder board covers like David Burns builds. That would allow you to use jars as gravity feeders in the top, but would not allow the bees to get into the box around the feeder.
I had the same problem.... I ended up having about 4 combs to take off the cover and what I did was i put the in a foundationless frame and they were'nt quite wide enough to touch both top and bottom bar so i sat it on the bottom bar and used rubber bands to hold it in place. its been about 3 weeks since ive done it and the comb that was rubber banded is completely attached to top and bottom bar. just make sure the comb is in the frames nice and straight. My bees are building alot of comb that seems to keep wondering away from the top bar and i've also had two combs on one frame which was kind of interesting lol so i guess what im trying to say is if the comb starts going in a wrong direction correct as soon as you can cause it doesnt take long for it to get messy